Water cooler device

For a detailed analysis of some aspects, you need to know what a cooler is. At a minimum, this is a device with which people can provide themselves with both cold and hot drinking water.

Water cooler device

The design itself includes a body, its upper part is a bottle of liquid. It is equipped with two faucets, they are intended for supply, however, there are models with three such products. As for the internal analysis, this is a system of various tubes and branch pipes. In addition to them, there are two tanks. One of them is responsible for cooling, and the other for heating. A valve is formed between them, it is thanks to it that the pressure is balanced, therefore, there is no mixing of two liquids with different temperatures. Do not forget about the water intake, through which the feed is made.

Flow cooler operation scheme

The named device is composed of a four-stage filter and an ultraviolet lamp. This promotes the use of a water source as a water supply. Therefore, you do not have to worry about the possible infection of bacterial particles, since they are completely eliminated inside the structure. In general, deep cleaning is performed. And due to the fact that running water is used, we can safely talk about the economy and the lack of restrictions on fluid intake.

Flow chart of a cooler

Speaking about this system, one cannot but mention the following components:

• Coal prefilter, which eliminates not only chlorine, but also various organic and chemical waste substances.
• Ultrafiltration filter. Thanks to it, such characteristic components as bacteria and viruses are removed. The reverse osmosis membrane also works well.
• Sedimentary. Water is purified from elements whose value is at least 5 microns.
• Compressor. It is necessary in order to establish a normalized pressure for converting the refrigerant into a liquid (the function is similar to a refrigerator).
• The carbon post-filter removes unwanted odors and smack from the water that may remain after passing through the membrane.
• Naturally, the device also has taps with tanks for dispensing cold and hot water.
• To ensure optimal performance, special pressure is necessary, which just helps to install a booster pump.

Principle of operation

After the main points on the varieties of the design are disassembled, we can proceed to the general provisions of the operation process.

REFERENCE! Activities are carried out from an electrical network equal to 220 volts.

How water is heated in the device

To begin with, the water in the required quantity fills a special compartment from the main compartment, which is designed for cooling and heating. When these containers lose a certain volume of liquid, they are refilled in new proportions.

IMPORTANT! This stage may differ in different production models. The cooler constantly maintains the degree that the user set. This happens using sensors. Therefore, you have the opportunity to get hot water without expectations.

This method is good in that boiling is not carried out (maximum 98 degrees heat), which means that the beneficial properties and taste are not lost. Heating takes place due to the built-in heating heater - a standard system similar to the activities of a kettle and similar inventions. The element itself can be both internal and external. This is relative to the tank.

How water is cooled in the device

This aspect can be divided into two, namely electronic and compressor. The second of them is most similar to the process of the refrigerator. To prevent the destruction of the ozone layer, a refrigerant is used, thereby ensuring environmental safety. In addition, here you can emphasize the speed and speed of lowering the temperature.

The first of these systems is equipped with two plates, which, in fact, are semiconductors. One of them is heated during the supply of electric current, and the other is cooled. Therefore, different degree measurements are obtained.

Exploitation

ATTENTION! It is strongly recommended not to connect the structure when there is no fluid inside. And also refrain from using up to three hours after installation. And do not forget about the possible danger and electric shock. If you still have problems or various malfunctions, you should worry about security and unplug the device from the outlet.

Use is based on the instructions and certain requirements:

• Install the unit on a smooth surface, the gap from it to the wall should be no less than 10-20 meters.
• Protect the apparatus from cheese rooms and from sunlight.
• Do not place near heating, heating, electrical devices.
• Before use, wait two to three minutes so that the tanks are completely filled with water.
• The power line to which the cooler is connected must be with a grounded contact.
• The bottle should be upright. After removing the hygienic film, and then turning it downside down.
• In the case when the building has not been used for a long time, cleaning should be done using cleaning agents. This is to avoid contamination.

Periodic monitoring of fluid levels is recommended. When it ends, you need to install the switch. At a time when new products are in place, it is advisable to wait a while to fill the internal system completely. And only then proceed to turn on.