How to disassemble the monitor

Of course, every device tends to break. To troubleshoot, sometimes you first need to disassemble the structure. However, not everyone knows how to do it right. Thus, in this article we will try to analyze in detail the specifics of the monitor parsing, as well as touch upon the points that are strongly not recommended in the process.

Even the novice master can perform the procedure (open the monitor), but it is important that everything is done with the utmost care and accuracy, since the equipment is fragile enough and can easily be damaged.

What is required

Of course, before the main stage it is necessary to arm yourself with certain items, which, accordingly, will be needed. The following is a list:

• Small screwdriver;
• Tweezers;
• Wedges made of wood;
• Sharp blade of a knife;
• Soft fabric in order to lay the structure on it. It can be either a blanket, a plaid, or any carpet.

Prepare the monitor for analysis

It is important to understand that in order to carry out really expedient work, you need to prepare your workplace. This is necessary so that in the process you cannot be prevented and prevented in order to achieve your goal. Thus, for starters, the user will most likely need to remove the leg on the screen. Most often, one can notice such a mount where screws are used that connect the case to the main part. Naturally, they should be unscrewed and carefully removed.

As for the rear panel, this is the possibility of using not only a small screwdriver and wedges, but also due to screwdrivers in the amount of two pieces. Therefore, for this you need to first push one of them into the hole between the rear and front panels, and then carefully push them apart. The next step will be the penetration of the same product, however, already in a lateral state.

With forward movements, it is desirable to smoothly penetrate by swinging two sides. Issuing a click will mean reaching the goal - the sash has opened. Holding all the details, it is necessary to separate the sidewalls from the latches until the back of the monitor is completely open.

ATTENTION! In order not to harm the surface, you can use certain tools that can easily be purchased in special stores.

Instructions on how to disassemble the case

After the preparation stage, accordingly, you can already proceed to the main sequence of actions, which are described below:

1. The first step is to deploy the monitor with the front side down. From the same angle, you can see the latches that need to be unfastened with tweezers, thereby pushing the cover back.

REFERENCE! It is recommended to do this as carefully as possible, leaving a gap of half a centimeter to one. This need is explained by the fact that there is a possibility of damage.

1. Next, it is worth arming yourself with one wooden wedge and stick it directly into the hole made. It is necessary so that the gap could not slam.
2. Therefore, the same manipulations must be carried out with other places where the latches are. How many of them can not be predicted in advance, since each model of the screen has its own quantity.
3. When you get to the upper parts, a screwdriver will help you. With its help, you can climb into fairly narrow places, while you should slightly press on the surface.

IMPORTANT! It is at this point that the risk of damage is high, so it is highly recommended that you perform it slowly and carefully.

So usually after such fraud the cover is quite easy to remove. After opening you will see a metal casing.

What not to do / not recommended

Of course, there are certain points, the commission of which can lead to unpleasant, and sometimes fatal consequences. Thus, a list of the following undesirable things is provided for your attention:

• Use a large screwdriver. Since the material with which you interact is quite fragile, heavy objects can cause various damage.
• In principle, disassembly should only be carried out when the user is 100% sure of the need and the resulting utility. This is due to the fact that most often it will be more advisable to contact a qualified master of their craft.
• The work itself must be carried out in complete safety.

ATTENTION! The device must be disconnected from the power source.

• The procedure is best done directly on the floor. Otherwise, if the structure falls even from any height, the owner is ensured a lethal outcome of the equipment. Therefore, in a better situation, the monitor will have nowhere to go, which acts as a guarantee of the preservation of your structure.