Constantly snaps electric stove gas

Modern technologies represent the maximum convenience and comfort for cooking for the owner of the kitchen. After a year, it became possible to forget about matches and lighters, because now there is auto ignition. Nevertheless, there are two ways to set fire to a burner: manual and built-in. And if everything is clear with the malfunctions of the first of them, then the second question arises. The reasons and methods for their elimination will be described in this article.

The principle of auto ignition

To identify the cause, you need to know how the device works. Dealing with this is not difficult. The ignition system is powered by the network, therefore, hence the name - electric ignition. It is found only in gas stoves.

First you need to press the handle and turn it to the side, moving along the arrow, which is shown on the unit panel itself. The principle of operation of this element is as follows:

• When you press, spark conversion starts with the flow of electrical impulses.
• When you turn the knob, the gas supply is turned on, which is directed to the burner.
• The spark interacts with the gas, resulting in the formation of fire.
• As a result, the spark ignites the gas.

You can release the handle after a few seconds have passed. This is necessary to magnetize the system. Of course, the whole process is much faster than it was described. The hotplate to which the spark signal has been applied is switched on. To start the button, its location can be found near the knobs. It has a current of two hundred watts. There is a guarantee that with periodic or constant changes in the network, you are insured against interruptions in the device itself. If we consider old devices, then here a little different happens. A spark is given on all burners, and only one is turned on - in which gas is open.

REMEMBER!

The whole system will work in one case - only when the plug is connected to the home network.

Why it can click electric ignition of a gas stove

The basis may be different, however, none of them are scary.

1. If you notice a sound after washing dishes or cleaning the stove, this may be due to moisture.
2. Contact oxidation occurs, which closes the circuit.
3. Sticking of the contact and its oxidation by getting carbon deposits in the button of the electric ignition system.
4. Due to overheating or combustion, one button breaks down, and then a circuit may short circuit.
5. The button simply got stuck because too often grease or dirt got into it.
6. Water penetration into the ignition function switch.
7. Incorrect operation of the stove.
8. Knocks out a circuit breaker in the apartment shield at startup.
9. If clicks are heard and there is no spark, this means that there is no gas.

IMPORTANT!

If none of the reasons is noted, it is better not to take action on its own to eliminate it. You should contact a special service.

Contacting special services is a guarantee of the safety of the whole family, since a gas stove is a dangerous device, under one incorrect set of circumstances, and the real problem can turn into large sizes.

Basic troubleshooting methods

To eliminate the source of a defect in the work, it is necessary to take measures. Namely:

• Eliminate moisture. Due to salts in the liquid, which, in essence, appear to be current conductors, contact closure occurs.
• Disassemble the design and dry the button.
• Remove the old one and replace the new electric ignition.
• Simple cleaning.
• Make sure that only one button does not work, to do this, turn on the next burner; if ignition does not occur, then repair the button.

What if the piece constantly clicks on its own

Find sources of trouble. Then follow the instructions for eliminating work defects that are written in this article. Refresh all your knowledge of this. It is important not to panic in any situation, strictly follow the rules, only then the outcome of the events will be favorable.

REMEMBER!

Most damage can be repaired on their own - they are harmless.

How to fix a malfunction at home

Here are steps that can help remove a possible malfunction.

• For example, when the reason is water, that is, due to the constant ingress of liquid on the stove, it is necessary to dry the device well. You should unplug the plug, turn off the device for several days (two to three are recommended). During this time, the device should have time to dry. If, after this procedure, the click remains, then you already have to call special masters who are sure to cope with the task.

ATTENTION!

In no case do not use the oven when drying, otherwise moisture will collect in huge quantities, let it evaporate naturally.

• When braking a button (using a spring) due to accumulation of grease and dirt, you need to release the handle and thoroughly clean it with a brush and allow the stem to dry. It is not guaranteed that clicking will be on its own, as before. There is an option when the button, due to the low landing, will not fully press.

REFERENCE!

For a more productive cleaning, use a soap solution.

The unit must be replaced in case of prolonged use of the unit. This is a natural phenomenon, so that in such a situation sounds can be avoided in only one way.

• If only one burner does not work, then the thing is that the wire is damaged, the fault lies in the channel of the whole unit.
• If the burner is out of order, it should be replaced.
• However, with a continuous repetition of a click, it is worth using ignition with a lighter or matches.
• Or call a professional craftsman who can qualitatively diagnose the cause and repair your equipment.

The main thing is that when a breakdown is detected, do not panic, but act sequentially.