How to color the refrigerator

Surely many in the garden or in the country have an old refrigerator, the look of which has long been pleasing to the eye. Sometimes people do not realize that it can be updated and it will fit perfectly into the interior.

If your refrigerator is still in good condition, but its appearance is depressing, feel free to take up the restoration. You yourself will be surprised at the result, and at the same time only your desire, minimal experience and small financial investments are required. Why spend money on new equipment if you can make an old designer?

The best options for painting the refrigerator outside

Not sure how you would like to see your refrigerator? Do not know how to draw and fantasize? It does not matter, because today on the Internet it is easy to find many simple and unusual solutions. Everyone will choose among them what is suitable specifically for his case and interior.

Video ideas:

Basic rules for quality painting

In order for the paint to lay down well and serve for a long time, it is necessary to successfully select it and strictly observe the painting technology during operation.

How to choose the right paint

For restoration, paint and a minimum of tools will be required. Only a narrow roller and brush are needed, and if aerosol cans are used, even they are not needed. The selection of the coloring composition is a responsible matter, because it must not only perform a decorative function, but also protect the equipment from various mechanical damages. Therefore, paints are required, satisfying certain requirements: easily tinted, hold paint vertically, resistant to detergents.

For this purpose, waterproof metal paint suitable for indoor use is suitable. It can be polyurethane, acrylic, oil, automotive nitro enamel, zinc, silicone, epoxy, nitrocellulose or other paint. They all differ in composition, but in this case it does not matter.

Coloring substances can be dull, glossy, luminescent, smooth or textured, vary in color, have different drying times, cost. The most budgetary, harmless and simple option is acrylic paint for metal.

Staining steps

Before you begin the process of dyeing the technique, it is necessary to carry out some preparatory work so that the paint lies evenly and smoothly.

Preliminary work:

1. Disconnect the refrigerator from electricity.
2. Remove the shelves and trays inside.
3. Clean the outside of dirt and grease. This can be done easily with a stiff sponge and grease cleaner.
4. To keep the paint better, remove the old coating with sandpaper, sand chips and scratches.
5. Wipe off the dust with a wet rag, and then wipe it dry.
6. Degrease the surface using special chemistry.
7. Apply a primer if necessary.
8. Protect your hardware with cling film, wide tape or masking tape.
9. Cover the floor with newspapers or oilcloth and other surfaces that may be dirty during painting.
10. Start by painting the inconspicuous area.

Dyeing

Attention! When working for safety, the use of personal protective equipment is necessary. In this case, a respirator and rubber gloves act in their role.

It is best to carry out staining on the street in warm and calm weather. If this is not possible, a bright, well-ventilated room is suitable. But in this case, it is better not to use car paint in cylinders, since it is the most toxic.

Rules for staining:

1. Apply the coloring composition in 2-3 layers.
2. After each layer, you need to take a break for 30 minutes, so that it dries well.
3. When painting, the roller or brush is more convenient to move from left to right or from top to bottom.
4. Hard-to-reach areas are easily painted over with a small brush.
5. As the last layer, to give the surface a gloss or dullness, you can use aerosol acrylic varnish.

Aerosol staining technology

When painting with aerosol cans, they must be kept at a distance of 30 cm from the surface to be painted. At the same time, make all movements evenly and non-stop, so that no paint build-up occurs. If it is necessary to remove minor paint defects, use solvents.

Creative dyeing and decoupage technology

• Want your old fridge turned into a writing board? It can be used to write recipes, notes to relatives and show guests an original solution.
• Kitchen appliances can be painted not in the same color, but by adding colorful stripes or geometric shapes. At the same time, it is convenient to use a masking tape on color transitions for a more accurate result.
• Painting or finished stencil will also be a good solution. The stencil can be easily made with your own hands.
• Decoupage. Sometimes people do not want to bother with staining, but prefer to update the refrigerator using a film. But this method requires good dexterity and experience in order for the film to lie evenly and without bubbles. But there is an easier option - this is decoupage. His technique is very simple and accessible even to a student. It almost does not require cash investments and takes a minimum of time. Decoupage application made of paper, which is varnished for practical use. Decoupage cards, multilayer paper napkins are suitable for this. You can also cut pictures from magazines, draw on your own or print from the Internet using a color printer.

As you can see, the procedure for painting the refrigerator is simple and can easily be done at home on your own. It only takes time and your imagination. Give your refrigerator a new life, and you will noticeably transform the old interior of your kitchen.